Xerox Versant 180 Press User Manual Download | Manualshive

Page: 24 / 166

background image

Important

Always use the Power On/Off button first, and then power off the Main Power Switch.

Power On/Off the Press

Power On the Press

1. Check that the Main Power switch behind the Front Door is On.
2. Press the Power On/Off button on top of the press to the ON position.

The Ready Indicator light displays green.
A screen message advises of a short wait while the fuser warms up and the press runs
a system check. You can set features for a job during this time and the printing process
will start automatically when the press is ready.

Power Off the Press

Important

Always power off the Power Switch first and then power off the Main Power Switch.

1. Press the Power On/Off button on the top of the press to Off.

Wait until the lights on UI stop blinking, as this allows the fuser to begin cooling.

2. Switch Off the Main Power switch behind the Front Door.

Note

Allow the press to remain off for a minimum of 10 seconds before switching on the
power again.

Power Saver

The Power Saver feature allows the press to enter a reduced power consumption mode
when all print jobs have completed and there are no jobs currently processing. There
are two energy saving modes: Low Power and Sleep.

By default, the press automatically enters the Low Power mode after 1 minute of
inactivity. After 1 minute of inactivity, the press then enters Sleep mode. These time
intervals for both modes can be changed by the system administrator.

Refer to the following example:

• Low Power Mode is set to 1 minute.
• Sleep Mode is set to 10 minutes.
• Sleep Mode activates after 10 minutes of total inactivity and not 10 minutes after

the Low Power Mode begins.

Low Power Mode

In this mode, the power to the User Interface (UI) and fuser unit is lowered to save
power. The display goes out and the Energy Saver button on the UI lights. To use the
press, press the Energy Saver button. The Energy Saver button is no longer lit, indicating
that the Energy Saver feature is canceled.

Xerox

®

Versant

®

180 Press

2-8

User Guide

Getting Started

«
...
22
23
24
25
26
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

Brand: Canon Pages: 300

Brand: Canon Pages: 288

Brand: Canon Pages: 58

Brand: Canon Pages: 30

Brand: Xerox Pages: 341

VarioPrint 1055

Brand: OcÃ© Pages: 194

Brand: Oce Pages: 12

Brand: Tally Pages: 53

T2265 SprintPro

Brand: Tally Pages: 30

Brand: Tally Pages: 108

Brand: TallyGenicom Pages: 2

Brand: TallyGenicom Pages: 2

Brand: Xerox Pages: 324

16C0365 - 5500 MFP

Brand: Lexmark Pages: 88

1900N - B/W Laser Printer

Brand: Kyocera Mita Pages: 286

ESP Office 6100 Series

Brand: Kodak Pages: 94

Brand: Gestetner Pages: 144

ColorQube 9303 Series

Brand: Xerox Pages: 1812

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands