Xerox Versant 180 Press User Manual Download

Page: 141 / 166

Problem

Smear 208 mm from the Lead Edge

Suggested Solutions

Confirm the media being used is compatible with the press, is within supported specifica-
tions, and in good condition.

Change the Adjust Paper Speed at Transfer Module setting.

• Use this feature to adjust the paper speed in the transfer unit.

• The option can be found in Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Adjust Paper
Speed at Transfer Module > Change Settings.

• Based on the output, decrease Adjust Paper Speed at Transfer Module in increments

of 0.05%. After every increment adjustment run test prints and evaluate the output to
determine if additional adjustment is necessary.

• Transfer defects may occur when paper speed is too fast or too slow.

Change the Adjust Fusing Speed setting.

• This feature can be used to correct the issue of a smear at 208 mm from the Lead Edge

(LE). Increase the fuser speed to correct the issue.

• This feature also impacts print quality.

Increasing fuser speed extends the image. If fuser speed is set too high it may
cause paper jams.

Decreasing fuser speed shrinks the image.

• The option can be found in Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Adjust Fusing
Speed > Change Settings.

• Increase fuser speed in increments of 0.5%. After every increment adjustment run test

prints and evaluate the output to determine if additional adjustment is necessary.

Problem

Trail Edge Deletions

Suggested Solutions

Change the Adjust Image Transfer for Trail Edge setting.

• This feature is used to adjust the voltage ratio on the Secondary Bias Transfer Roll (BTR),

where the image is transferred from the belt to the paper.

• This feature can be found in Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Adjust Image
Transfer for Trail Edge > Change Settings.

• Decrease the Adjust Image Transfer for Trail Edge in increments of 5 to 10%. After every

increment adjustment run test prints and evaluate the output to determine if additional
adjustment is necessary.

6-19

Xerox

Versant

180 Press

User Guide

Troubleshooting

Summary of Contents for Versant 180 Press







































































































































































Search results

Summary of Contents for Versant 180 Press

Reviews:

Related manuals for Versant 180 Press

Brands by name

Popular brands

Xerox Versant 180 Press, User Manual

Search results

Summary of Contents for Versant 180 Press

Reviews:

Related manuals for Versant 180 Press

Brands by name

Popular brands