Xerox Versant 180 Press User Manual Download | Manualshive

Page: 133 / 166

background image

Custom Paper Settings Troubleshooting

This section helps you locate and resolve specific problems through the use of the Custom
Paper Settings. In addition, for in depth information on the features referenced on the
table, refer to the System Administration Guide.

Initial Actions

Perform these actions first to improve print quality:

• Confirm the media being used is compatible with the Press, within supported

specifications, in good condition, and has been assigned to the correct Press Tray.

Secondary Actions

If problems are not resolved after performing the suggested actions below, contact the
Customer Support Center.

Problem

Multifeeds, Misfeeds and Paper Jams in Trays 6-9

Suggested Solutions

1.

Change the Adjust Air Assist Values setting.

• Use this feature to adjust the amount of air volume generated by the tray blowers which

assist in separating sheets when feeding paper. When using light-weight or heavy-weight
paper, which stick together easily, select a stronger air flow setting in order to better
separate sheets and prevent paper jams or multifeeds.

• This feature can be found in Machine Status > Tools > Setup & Adjustment > Custom

Paper Settings. Select the desired Custom Paper > Change Settings > Adjust Air Assist
Values > Change Settings.

• The settings available for this feature are:

-

System Default: The air volume is set to the appropriate amount based on the
Stock and environmental conditions.

-

Multifeed Support Table: Select this option if you use paper that tends to trigger
multifeeds. This setting increases the air volume to a level higher than System
Default.

-

Mis-Feed Support Table: Select this option if you use paper that tends to trigger
paper jams. This setting increases the air volume to a level higher than Multifeed
Support Table.

-

Forced Off: Select this option when working with special media that tends to jam
as a result of the air flow that is introduced by Adjust Air Assist Values. This setting
turns off Adjust Air Assist Values.

2.

Change the Tray Heater setting.

• Use this feature to Enable (checked) or Disable (unchecked) the tray heater. The tray

heater warms the air that is blown into the tray by Adjust Air Assist Values to help
prevent paper jams and multifeeds by loosening contact between sheets.

6-11

Xerox

®

Versant

®

180 Press

User Guide

Troubleshooting

«
...
131
132
133
134
135
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

Brand: Olympus Pages: 71

Brand: Magicard Pages: 30

Brand: Magicard Pages: 35

MAGICARD ID Card Printer

Brand: Magicard Pages: 30

Brand: Magicard Pages: 6

WorkCentre 5325

Brand: Xerox Pages: 160

WorkCentre 5016

Brand: Xerox Pages: 2

WorkCentre 490cx

Brand: Xerox Pages: 258

WorkCentre 4260 Series

Brand: Xerox Pages: 210

WorkCentre 3550

Brand: Xerox Pages: 32

WorkCentre 3315DN

Brand: Xerox Pages: 191

WORKCENTER 5222

Brand: Xerox Pages: 28

VersaLink C71 Series

Brand: Xerox Pages: 247

VersaLink C7000

Brand: Xerox Pages: 2

Brand: Xerox Pages: 21

VersaLink B71 Series

Brand: Xerox Pages: 234

WorkCentre 6505

Brand: Xerox Pages: 4

WorkCentre 6015

Brand: Xerox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands