Xerox Versant 180 Press User Manual Download | Manualshive

Page: 113 / 166

background image

Cleaning the Fuser Assembly

If you see dry ink/toner debris on the back side of the print output, select and run the
Clean Fuser Assembly routine from the press UI to clean the fuser component and
address this image quality issue caused by contaminants in the fuser.

Note

If you still notice contaminants on the back of the prints after running this procedure,
contact Service. Dry ink/toner debris may be coming from the Transfer roll area instead
of the fuser.

1. Press the Machine Status button on the UI.
2. Select the Tools tab.
3. Select Setup & Calibration > Clean Fuser Assembly.
4. From the screen that displays, specify the paper tray to use and the number of blank

sheets to print for the "Clean with Paper" method of removing the unfused dry
ink/toner.

5. From Paper Supply, select the paper tray to use.

Note

Any type of paper and size can be used. However, the smooth surface of coated paper
does offer more contact area to the pressure roll.

6. From Number of Sheets, select the number of blank sheets to print (1 to 5).

Note

For best results, run a minimum of 5 sheets.

7. Select Save.
8. Press the Start button.

The system begins the cleaning process and displays a "successfully completed"
message when finished.

9. Select OK.

Note

The process with 5 sheets of paper will take approximately one minute.

Replacing Consumable Supplies

The following items are the Customer Replaceable Units (CRU) for the press. It is
recommended that you have a supply of these items available to eliminate down time
when they need to be replaced.

• Dry Ink/Toner cartridges (C, M, Y, K)
• Drum cartridges (C, M, Y, K)
• An empty Waste Dry Ink/Toner bottle
• Suction Filter

Refer to

for the latest consumable part numbers.

5-5

Xerox

®

Versant

®

180 Press

User Guide

Maintenance

«
...
111
112
113
114
115
...
»

Summary of Contents for Versant 180 Press







































































































































































Reviews:

No comments

Related manuals for Versant 180 Press

imageCLASS Mf6160dw

Brand: Canon Pages: 64

imageCLASS MF6500 Series

Brand: Canon Pages: 132

imageCLASS MF5550

Brand: Canon Pages: 120

imageCLASS MF5630

Brand: Canon Pages: 85

imageCLASS MF5550

Brand: Canon Pages: 136

IMAGECLASS MF7400

Brand: Canon Pages: 40

imageCLASS MF5850dn

Brand: Canon Pages: 34

imageCLASS MF6500 Series

Brand: Canon Pages: 16

imageCLASS MF6540

Brand: Canon Pages: 82

imageCLASS MF5550

Brand: Canon Pages: 99

imageCLASS MF5630

Brand: Canon Pages: 24

imageCLASS MF5770

Brand: Canon Pages: 2

imagePRESS C7000VP Series

Brand: Canon Pages: 48

imageClass MF5650

Brand: Canon Pages: 40

imageCLASS MF5770

Brand: Canon Pages: 8

imageCLASS MF4880dw

Brand: Canon Pages: 36

imageCLASS MF4890dw

Brand: Canon Pages: 116

ImageCLASS MF4690

Brand: Canon Pages: 387

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands