Note
It may be possible to configure your Xerox Nuvera with two or more SFMs, effectively doubling the feed
capacity of the system. See your Xerox sales representative if you wish to configure your system in this
way.
Fan the paper first
To aid in sheet separation and to prevent jams, always fan the reams of paper before loading into the
trays. To do so:
1. Place the new stack of paper on a flat surface.
2. Place the palm of your hand on the center of the stack to hold it firmly.
3. Place the other hand at one corner of the stack and fan through the paper.
4. Repeat this procedure for each corner.
5. Discard the top and bottom sheets of paper from the ream.
To load paper
For details on paper handling and storage, see
.
Caution
Do not overload paper trays. Do not block or damage the stack height sensor.
1. Open the tray.
2. Move the paper guides apart.
3. If changing to a different sized stock, remove any unused stock from the tray.
4. Fan the paper ream before loading it into the tray and make sure the paper is in good condition.
5. Place a ream of paper in the center of the tray between the guides, making sure the feed direction
is correct.
6. Move the paper guides inward until they touch the paper stack. Make sure the side and trail edge
guides are snug against the stack after loading the first ream.
7. Add more paper to the tray, up to the MAX line.
8. Make sure the height sensor is not pinned down by the paper stack. The stack height sensor is located
on the inside of the right paper guide. Remove any excess paper.
9. For Tray 2 of the 4-Tray SFM a Rear Guide Stop is installed and configured for either 8.5 x 11" or A4
stock. It is designed to stabilize the rear guide in the tray and improve registration. When loading
this tray with these stocks, enable the Rear Guide Stop by lifting and rotating the lever to the right.
Disable this guide for all other paper sizes used in this tray by lifting and rotating the lever to the
left.
Note
The stop guide is set to either 8.5 x 11 " or A4 paper size. If you need to change from one of these
sizes to the other, you must contact Service.
10. For tray 3 or 4, adjust the green baffle at the back of the tray to prevent the paper stack (11 x 17
inch and larger) from skewing when closing the tray. Properly adjusted, it should make light contact
(or be within a few millimeters) with the loaded paper stack. The trays in the 2-Tray Feed Module do
not have the green baffles.
11. Close the tray.
12.
on the control screen to match the paper you just loaded if you have not
already done so.
Xerox
®
Nuvera
®
11-6
User Guide and Training Aid (UGTA)
Setup Paper Trays
Summary of Contents for Nuvera
