Xerox DocuPrint P14 User Manual Download Page 124 | Manualshive

Page: 124 / 133

background image

Memory and PostScript SIMMs

D-4

❖

DocuPrint P14 User Guide

Memory and PostScript SIMMs

Additional printer memory and the PostScript option are
provided on SIMMs (single inline memory modules). This
procedure is applicable to either option.

Review the precautions on page D-3 and then follow this
procedure to install SIMMs in your computer.

Since PostScript requires 12 MB of printer memory and the
DocuPrint P14 comes with 4 MB standard, installation of
the PostScript SIMM requires installation of a memory
SIMM as well.

Be sure to consult the

Supplies/Options Guide

that came

with your printer for supported memory SIMM
specifications.

1

Turn the printer power off and disconnect the power cord
and printer cable.

2

Remove the cover located at the right side of the printer.

«
...
122
123
124
125
126
...
»

Summary of Contents for DocuPrint P14






































































































































Reviews:

No comments

Related manuals for DocuPrint P14

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brand: Oce Pages: 41

Brand: Oce Pages: 28

Brand: Oce Pages: 6

Brand: QMS Pages: 104

Brand: Oce Pages: 386

Brand: Oce Pages: 2

Brand: Oce Pages: 27

Brand: Oce Pages: 324

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

Aficio SP4100N-KP

Brand: Ricoh Pages: 4

Brand: BCS Pages: 151

Brand: Lexmark Pages: 500

Brand: Patton electronics Pages: 16

WorkCentre 7328

Brand: Xerox Pages: 8

Brand: Oki Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands