manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 274

1-252

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-64 Inverter Clutches (PL 9.4)

Removal

1.

Remove the Exit Drive Assembly (RRP 1-55).

2.

Remove the four black machine screws securing the Drive Support to the 
Inverter Bracket, and lift the Support off of the Bracket.

3.

Disconnect P/J218 and P/J219, and free the wire harness from the harness 
clips.

4.

Slide the Counter-Clockwise Gear off of the Counter-Clockwise Clutch.

5.

Slide the Clockwise Gear off of the Clockwise Clutch.

6.

Lift the Counter-Clockwise Clutch off of the bearing, and remove the Clutch.

7.

Lift the Clockwise Clutch off of the bearing, and remove the Clutch.

Fig 1-86  Inverter Clutches

Counter-Clockwise Clutch

Clockwise Clutch

S4525-135

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands