manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 266

1-244

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-56 Exit Gate Solenoid (PL 9.1)

Removal

1.

Remove the Fuser Cover (RRP 1-1).

2.

Disconnect the Exit Gate Solenoid J210 from the wire harness.

3.

Remove the wire harness from the harness clips.

4.

Remove the two black machine screws securing the Exit Gate Solenoid to the 
Offset Assembly, and remove the Solenoid.

Replacement

1.

Position the Exit Gate Solenoid so the wire harness faces up.

2.

Reinstall the Solenoid onto the Offset Assembly, making sure the crossbar of 
the solenoid plunger latches onto the Solenoid Link.

3.

Use the two screws (removed in Step 4 above) to secure the Solenoid to the 
Assembly.

4.

Reconnect J210.

5.

Secure the wire harness to the harness clips.

6.

Reinstall the Fuser Cover (RRP 1-1).

Fig 1-78  Exit Gate Solenoid

S4525-127

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands