manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 248

1-226

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-34 Multi-sheet Bypass Feeder Friction 
Clutch (PL 4.3)

Removal

1.

Remove the Multi-sheet Bypass Feeder Tray Assembly (RRP 1-26).

2.

Remove the E-ring securing the Clutch to the shaft.

3.

Rotate the Clutch clockwise as you pull it off of the shaft.

Replacement

1.

Make sure the Spacer is in place on the Clutch shaft.

2.

Rotate the Spacer so the tabs on the Spacer mesh with the notches on the 
Clutch Gear.

Caution

When performing step 3 below, push only on the rear of the 

Clutch. Never press the sides of the Clutch. Pressing the sides of 
the Clutch may break the Clutch.

3.

Slide the Friction Clutch onto the shaft, rotating the Clutch as you slide it toward 
the Spacer.

4.

Make sure the Clutch and Spacer mesh.

5.

Use the E-ring (removed in Step 2 above) to secure the Clutch to the shaft.

6.

Reinstall the Top Cover.

7.

Reinstall the Multi-sheet Bypass Feeder Tray Assembly (RRP 1-26).

Fig 1-64  Multi-sheet Bypass Feeder Friction Clutch

S4525-107

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands