manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 205

Volume 1 / Print Engine - FRU RRPs

1

-

183

Removal and Replacement Procedures 
(RRPs)

This section contains the removal and replacement procedures for selected parts of the 

printer.  Not all Replacement Procedures are included in this Quick Reference Guide.  In 
most cases, to reinstall a part, simply reverse the Removal Procedure shown.  In some 

instances, the Replacement Procedure is included because it may contain special steps.

Preparation

Before you begin any Removal and Replacement Procedure:

1.

Switch OFF the printer power and disconnect the power cord from the AC wall 
outlet.

2.

Remove the Laser Print (EP) Cartridge and protect it from exposure to light by 
covering it with a piece of opaque plastic sheeting or by placing it in a light-tight 
container.  See RRP 48 for details.

3.

Disconnect all computer interface cables from the printer.

4.

Wear an electrostatic discharge wrist strap to help prevent damage to the 
sensitive electronics of the printer circuit boards.

5.

Wait at least 30 minutes after you have switched OFF printer power for the 
Fuser to cool before you work on or around the Fuser.

Work Notes

Note

Names of parts that appear in the RRPs may not be exactly the 
same as the names appear in the Section 12 Parts List. For 

example; a part called the Metal Registration Roller in an RRP 
may appear on the Parts List as Registration Metal Roller.  When 

working on an RRP, ignore any prerequisite RRP if you have 
already performed that removal procedure.

Caution

Always use the correct type and size screw. Using the wrong screw 

can damage tapped holes. Do not use excessive force to either 
remove or install either a screw or a printer part. 

Warning

Unplug the AC power cord from the AC wall outlet before 

removing any printer part.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands