manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 194

1-172

DocuPrint N4525 Network Laser Printer - Service Guide

Component Control Output Tests

Component Control Output tests are used to aid in verifying proper component operation 

and identifying problems and isolating faulty components.  To access the following tests, 
you must enter Diagnostics Mode:

1.

Enter Diagnostics Mode - press and hold [2] and [6] while powering up the printer.  

Continue holding [2] and [6] until *IOT?* is displayed.

2.

Release [2] and [6], then press and hold [4] until “Main Menu” appears in the top line 

of the display.  You are now in Diagnostics Mode.

3.

Use the Control Panel Test Legend below to help navigate throught the various items in 

the Component Control Output table.

4.

Press [1] or [5] until “Main Menu Comp Output Test” is displayed.

5.

Follow the table headings, and the Control Panel Test Legend below, to navigate to the 
desired test.

The tests in the table below enable the technician to test the many output 

devices performing work inside the printer.  

Control Panel Test Legend:

Nomenclature Legend:
IOT

: Print Engine - the printer not including the 

System Controller Board or options.

HCF

: High Capacity Feeder Option

MBF (or MSI)

: Multi-sheet Bypass Feeder

ENV

: Envelope Feeder Option

Fin

: Finisher Option

Table 1-107 Component Control Output

Press [1] or [5] to display: Main Menu

Comp Output Test

Press [2]  or [6] to 
display: 

ß

Press [3]  or [7] to 
display: 

ß

Turn -On
Duration

Comment

Comp Output Test
IOT Unit

Main Motor On

2 min.

Press [4] to start test.
Actuate Main Drive Motor for duration or
Press [0] to stop.

Fuser Fan High

2 min.

Press [4] to start test.
Actuate Fuser Fan for duration or
Press [0] to stop.

LVPS Fan High

2 min.

Press [4] to start test.
Actuate Low Voltage Power Supply fan for 
duration or Press [0] to stop.

ROS Motor On

2 min.

Press [4] to start test.
Actuate Laser Scanner Motor for duration or 
Press [0] to stop.

ROS Motor Stadby

2 min.

Press [4] to start test.
Places Laser Scanner Motor in standby for 
duration or Press [0] to stop.

Tray 1 Lift Mot

2 sec.

Press [4] to start test.
Actuate Tray 1 Lift Motor for duration or 
Press [0] to stop.

Stop

Start

Menu Up

Item Up

Value Up

Menu
Down

 Item
Down

Value
Down

S4525-25B

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands