manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 159

Volume 1 / Print Engine - Troubleshooting

1

-

137

RAP 1-72

Skewed Image

.

PROBLEM

The image is either twisted on the page or is not parallel to the 
sides of the page.

THE PRINTER DISPLAYS NO ERROR CODE

.

Fig 1-27  Skewed Image

Table 1-96 Skewed Image

Step

Actions and Questions

Yes

No

1

PAPER FEED INSPECTION

Are the paper trays installed correctly, and is 
the paper correctly loaded into each cassette?

Go to step 2

Reload the 
paper and 
reinstall the 
cassettes.

2

PAPER PATH INSPECTION

Inspect the paper path, between the feed Tray and the 
exit Bin, for contamination or obstructions.

Is the paper path free of obstructions?

Go to step 3

Remove 
obstructions 
from the 
paper path.

3

FEED, PICK, AND RETARD ROLLER 
REPLACEMENT

Replace the Feed Roller, Pick Roller, and Retard Roller 
for the Feeder having the skew problem.

Is the image still skewed?

Go to step 4

Problem 
solved

4

REGISTRATION ROLLER REPLACEMENT

Replace the Registration Roller (RRP 1-45).

Is the image still skewed?

Go to step 5

Problem 
solved

5

LASER PRINT (EP) CARTRIDGE 
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Is the image still skewed?

Go to step 6

Problem 
solved

S4525-18

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands