Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 145

Page: 145 / 380

Volume 1 / Print Engine - Troubleshooting

123

RAP 1-65

Vertical Streaks

PROBLEM

There are black lines running vertically along the page in the
direction of paper travel.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-20 Vertical Streaks

Table 1-89 Vertical Streaks

Step

Actions and Questions

Yes

PAPER PATH INSPECTION

Inspect the paper path, between feed and exit, for
contamination or obstructions.

Is the paper path free of contamination or
obstructions?

Go to step 2

Remove
contamination
and
obstructions
from the
paper path.

LASER PRINT (EP) CARTRIDGE
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Are the vertical streaks gone?

Problem
solved

Go to step 3

IMAGE TRANSFER INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Grid Test Print and switch OFF printer

power halfway through the print cycle.

3. Open the Left Upper Door.
4. Open the Drum Shutter.
5. Hand rotate (counter clockwise) the Drum Drive Motor

flywheel to advance the drum far enough so you can
see the developed image area on the Drum before it
reached Transfer.

Before Transfer was the toner image on the
drum normal and without vertical streaks, but
there are vertical streaks on the paper after
Transfer?

Replace the
Bias Transfer
Roller
Assembly

Go to step 4

S4525-11

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands

Xerox DocuPrint N4525, Service Quick Reference Manual

Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands