Xerox C8130 User Manual Download Page 294

Page: 294 / 420

Paper Jams

LO C AT I N G PA P E R J A M S

Waarrnniinngg::

Parts that are near the fuser are hot. To prevent personal injury, never touch an area that has a

Caution label. Power off the printer immediately, then wait 40 minutes for the fuser to cool. After the

printer has cooled, try to remove the jammed paper. If the error on the control panel remains, contact
your Xerox representative.

Caauuttiioonn::

Do not attempt to clear any paper jams using tools or instruments. This action can damage the

printer permanently.

The following illustration shows where paper jams can occur along the paper path:

1. Door B

2. Bypass Tray

3. Door A

4. Left Tray

5. Duplex Automatic Document Feeder

6. Document Output Tray

7. Finisher Areas

8. Paper Trays 1–4

294

Xerox

AltaLink

C8130/C8135/C8145/C8155/C8170 Series Color Multifunction Printer User Guide

Troubleshooting

Summary of Contents for C8130





































































































































































































































































































































































































































Search results

Summary of Contents for C8130

Reviews:

Xerox C8130, User Manual, Page: 294 / 420

Search results

Summary of Contents for C8130

Reviews: