manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Share
Download
Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 94

Phaser 5400 Laser Printer Service Guide 

65

RAP 12 Error Code

 

E2-12: Tray 2 Jam

Open Tray 2

Error Code E2-13: Tray 3 Jam

Open Tray 3

A paper jam has occurred in the 2000-Sheet Feeder.

Table 32

Error Code E2-1: Paper Jam / Misfeed 2000-Sheet Feeder 

Troubleshooting Procedure

Step Actions and Questions

Yes

No

1

PROCEDURE

1. Open the 2000-Sheet Feeder Upper Rear Cover 

Assembly.

2. Remove the Jammed paper.

3. Run a test print.

Does the error message still appear?

Go to 
Step 2.

Problem 
solved.

2

PAPER INSPECTION

1. Pull out the 2000-Sheet Feeder Tray Assembly.

2. Check the paper condition and size.

Is the paper dry, in good condition and is the size 

within specifications?

Go to 
Step 3.

Replace with 
fresh paper 
of the proper 
size from an 
unopened 
ream.

3

FEED MOTOR ASSEMBLY

1. Switch printer power OFF.

2. Remove the 2000-Sheet Feeder Right Side Cover 

[RRP 12-5].

3. Open the Upper Rear Cover.

4. Manually rotate the top gear clockwise.

5. Inspect the rotation of the 2000-Sheet Feeder Motor 

Assembly.

Does the Feed Motor Assembly rotate smoothly?

Go to 
Step 4.

Replace the 
2000-Sheet 
Feeder Feed 
Motor 
Assembly 
[RRP 12.16, 

page 368

] or 

gears.

4

REPLACE FEED ROLLER [

RRP 12.14, 

page 366

]

Run Test prints.

Does the Error Code still appear?

Go to 
Step 5.

Problem 
solved.

5

TOP GEAR ROTATION

Manually rotate the top gear counterclockwise.

Does the 2000-Sheet Feeder Assembly rotate 

smoothly and feed a sheet of paper from the 

Feeder Tray Assembly?

Go to 
Step 6.

Replace the 
Feeder 
Assembly 
[PL 12.3, 

page 422

], if 

it does not 
rotate 
smoothly.

6

DRIVE ASSEMBLY GEARS

1. Remove the 2000-Sheet Feeder Tray Assembly 

[RRP 12.7, 

page 359

].

2. Rotate the gears of the Drive Assembly.

Do the gears of the Drive Assembly rotate 

smoothly?

Go to 
Step 7.

Replace the 
Drive 
Assembly 
[RRP 12.13, 

page 365

].

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands