manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Experience fast and efficient printing with the Xerox 5400N - Phaser B/W Laser Printer. Easily navigate through troubleshooting with the Service Quick Reference Manual, available for free download on our website. Enhance your printing experience with this reliable and high-quality laser printer. Download the manual from manualshive.com.

Share
Download
background image

Phaser 5400 Laser Printer Service Guide 

405

Table 137 PL 9.1 Electrical (1 of 2)

ID No.

Part Number

Qty

Name / Description

1

160K83452

1

Board, System Controller

2

1

Kit, Cover Assembly [includes 3~6]

3

1

Cover, Shield

4

2

Screw, Thumb

5

1

Cover, Print Engine Controller Board (MCU)

6

802K35520

1

Panel, Rear

7

105K19330

1

Board, 5 VDC Power Supply

8

105K19091

1

Board, High Voltage Power Supply (HVPS)

9

160K74360

1

Board, Duplex Interface

10

162K43530

1

Harness, Full DUP-1 [J502-J527]

11

162K43550

1

Harness, Flap-1 [J505-J528]

12

127K32011

1

Fan, Fuser Cooling

13

055E33041

1

Cover, Fuser Fan

14

162K43542

1

Harness, STK-1 [J504-J526]

15

162K42610

1

Harness, P/H [J12-J121, J128]

16

162K42640

1

Harness, Tray 2/3 Feeder [J13-P131]

17

162K42821

1

Harness, System Controller Board to User Interface 
[J18-J421]

18

162K42880

1

Harness, Laser NS [J11-J112, J114]

19

1

Harness

20

162K42740

1

Harness, Reg [J22-J222]

21

162K43521

1

Harness, Duplex Interface [J19-J501]

22

162K42720

1

Harness, HVPS [J18-J181, J183]

23

160K83415
160K83425

1

Board, Print Engine Controller [110 VAC] [US]
Board, Print Engine Controller 220 VAC] [EU]

24

733W14695
733W14696
733W14697
160K71940

As 
required

16 MB DIMM
16 MB DIMM
16 MB DIMM
8 MB Flash DIMM

25

650-4238-00

Drive, Hard Disk (20 GB)

S

600K76430

Kit, Hardware (includes screws and E-rings)

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5400N - Phaser B/W Laser Printer

Olympus P 400 Owner'S Manual preview
P 400
Brand: Olympus Pages: 71
Samsung SCX-3405FW Manual Del Usuario preview
SCX-3405FW
Brand: Samsung Pages: 347
Samsung SCX 6555N - MultiXpress Mono Multifunction Manual Del Usuario preview
SCX 6555N - MultiXpress Mono Multifunction
Brand: Samsung Pages: 180
Samsung SCX-4300 - SCX 4300 B/W Laser License Agreement preview
SCX-4300 - SCX 4300 B/W Laser
Brand: Samsung Pages: 18
Samsung SCX-4521FG - B/W Laser - All-in-One User Manual preview
SCX-4521FG - B/W Laser - All-in-One
Brand: Samsung Pages: 215
Samsung SCX 6320F - B/W Laser - All-in-One User Manual preview
SCX 6320F - B/W Laser - All-in-One
Brand: Samsung Pages: 332
Samsung SCX 4828FN - Laser Multi-Function Printer User Manual preview
SCX 4828FN - Laser Multi-Function Printer
Brand: Samsung Pages: 248
Samsung SCX 4725FN - B/W Laser - All-in-One User Manual preview
SCX 4725FN - B/W Laser - All-in-One
Brand: Samsung Pages: 253
Samsung ML 2851ND - B/W Laser Printer User Manual preview
ML 2851ND - B/W Laser Printer
Brand: Samsung Pages: 179
Samsung ML 2510 - B/W Laser Printer Manual Del Usuario preview
ML 2510 - B/W Laser Printer
Brand: Samsung Pages: 84
Samsung ML 1740 - B/W Laser Printer Manual Del Usuario preview
ML 1740 - B/W Laser Printer
Brand: Samsung Pages: 152
Samsung ML 1630 - B/W Laser Printer User Manual preview
ML 1630 - B/W Laser Printer
Brand: Samsung Pages: 142
Samsung ML 1630 - B/W Laser Printer Manual Del Usuario preview
ML 1630 - B/W Laser Printer
Brand: Samsung Pages: 82
Samsung SL-M2875FD Installation Manual preview
SL-M2875FD
Brand: Samsung Pages: 2
Samsung M337 User Manual preview
M337
Brand: Samsung Pages: 384
Samsung Lazett Combo SCX-4216F Service Manual preview
Lazett Combo SCX-4216F
Brand: Samsung Pages: 135
Samsung CLX-6260FD Manual Del Usuario preview
CLX-6260FD
Brand: Samsung Pages: 414
Samsung SCX 6555N - MultiXpress Mono Multifunction Administrator'S Manual preview
SCX 6555N - MultiXpress Mono Multifunction
Brand: Samsung Pages: 112

Brands by name

Popular brands

Load more brands