manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Share
Download
Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 299

270

Phaser 5400 Laser Printer Service Guide

RRP 2.9 Tray 1 Feed Solenoid 

(See 

PL 4.2 Paper Handler

)

Removal

Warning: Switch off the power and disconnect the Power Cord.

1.

Remove the MBF Assembly (RRP 2.1 Multi-sheet Bypass Feeder (MBF) 

Assembly).

2.

Remove the MBF Gear Cover (RRP 1.8 MBF Gear Cover).

3.

Remove the Pick-up Spring from the Tray 1 Pick-up Gear.

4.

Disconnect P/J135 from the Tray 1 Feed Solenoid.

5.

Remove the screw that secures the Tray 1 Feed Solenoid to the MBF Assembly.

Replacement

Reinstall the components in the reverse order.

Figure 59 Tray 1 Feed Solenoid

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands