XEMEX IQ0102065BNEM Installation Manual Download Page 1

1

Installation Guide 

On-site installation procedure PV monitoring with Xemex KWHIQ meter

Introduction

The Kwhiq IQ0102065BNEM electricity meter is a single-phase smart meter developed for measuring 
and monitoring energy to enable good energy management. Many energy parameters (such as 
energy, voltage, power, ...) are measured, logged and made available. The meter can be read and 

configured via the mobile network (4G / 2G).

The most important features:

Installation Guide

On-site installation procedure PV monitoring 
with Xemex KWHIQ meter

Measurement accuracy

Active power: EN 50470-3 Class B 

Reactive power: IEC 62053-23 Class 2 

MID certified

Connection

1 phase, 2 wires, direct connection

Rated voltage 

Voltage range

230V

+/- 20%: 184V – 276V

Rated current

Current range

5A

0.25A - 65A

Starting current

20mA

Frequency

50Hz (+/- 5%)

Internal power 

consumption

Voltage circuit: < 2W / 10 VA per phase. Current circuit: 0.5 VA per phase

Interfaces

 

– DLMS / COSEM via CAT M / GPRS / NBIoT mobile network

 

– Optical local interface DLMS / COSEM direct HDLC - IEC 62056-21

 

P1 port (SMR v5.0.2)

 

– LCD display with auto-scroll and push button for manual scrolling.

 

– 2 energy pulse LEDs: active 2000 imp/kWh & reactive 2000 imp/

kvarh

Real time klok

IEC 62054-21 
0.5s deviation over 24h at 23°C +/- 0.15 s/°C/24h
Backup by super capacitor to bridge 5 days of power failure

Mechanical

Dimensions: 210 x 131.6 x 85.5 mm Weight: 0.95 kg

Summary of Contents for IQ0102065BNEM












Reviews: