XciteRC 36001000 LEOPARD 2A5 Manual Download Page 18

18

Warnings and safety notes

36001000 LEOPARD  2A5

•  Always switch on the transmitter first, then the model. 

 

NOTE: 

during the operation of the transmitter must remain switched on!

•  Never operate your model with low transmitter batteries, because this reduces the range of your model dramatically.
•  If the drive battery is empty, the model first slow down until it no longer reacts properly to your commands. Stop the operation and 

change the drive battery or charge it again.

•  Pay attention to the instructions and warnings for this and any other equipment used by you (chargers, rechargeable battery packs, 

etc.).

• 

 WARNING:

 Keep packaging material, small parts, chemicals and electrical components away from children – 

risk of accident 

and injury!

• 

 ATTENTION:

 Do not drive against obstacles that the model cannot overcome, and stay on full throttle. This can destroy the 

motor, speed controller or the transmission!

•  The model and the transmitter may be neither get humid nor wet, especially the electronic components (receiver, speed controller, 

servo) and, if used, lithium batteries, are not waterproof! The model may not be used in the rain (or heavy fog), do not drive in wet 
grass or through puddles or snow. 

• 

 

WARNING:

 

Fire or explosion due to moisture in lithium batteries!

•  Plastic parts (eg. suspension and body) is less flexible and can break more easily at cold temperatures (below 10 ° C).
•  The modification of the model is not permitted for safety and CE approval regulations, which applies in particular to the transmitter, 

receiver and speed controller. Maintenance or repairs using original replacement parts are excluded.

•  The gears in the servo are made very precisely and with low tolerances, but also very small. Therefore never turn the front wheels by 

hand, which can seriously damage the servo.

•  After use, first turn off the model and then the transmitter. 

•  WARNING: 

remove the drive battery from the model and transmitter after use. Store the model never with built-in battery. 

Fire 

hazard!

•  Store batteries separately on a non-combustible surface.

•  The drive components (motor and speed controller) or the car battery may become hot during operation. 

 

WARNING:

 

Risk of 

burns!

 Let these components cool down completely after the operation (and also before each battery change)!

Operation of the model is performed solely at the risk of the operator. Only a careful and deliberate operation protects against physical 
injury and damage to property.

Handling precautions for batteries or rechargeable batteries

•  Keep batteries away from children! Never let batteries unattended, as they can be swallowed by children or pets!
•  Use only the recommended or equivalent type of batteries / rechargeable batteries.

• 

 WARNING:

 do not expose batteries / rechargeable batteries to heat or throw into fire - 

fire or explosion hazard!

• 

 WARNING:

 insert batteries / rechargeable batteries with the correct polarity, no short-circuiting -

 fire or explosion hazard!

•  If possible, always replace all batteries at the same time, never use new and used batteries and batteries with different charge levels 

simultaneously.

•  Do not use defective or damaged batteries or rechargeable batteries – fire hazard! Risk of chemical burns on contact with skin, use 

protective gloves!

• 

 WARNING:

 Do not attempt to recharge non-rechargeable batteries in a charger - 

fire or explosion hazard!

•  Remove the rechargeable batteries from the device before charging.
•  Charging may take place only with a suitable charger for the type of battery on a fireproof surface and under constant adult super-

vision – fire hazard!

•  Immediately remove used batteries from the devices.

• 

 NOTE:

 NiMH batteries must be checked at least every 3 months and, if necessary, recharged, otherwise because of the typic 

self-discharge they may get deep discharged and damaged! Therefore, better use so-called RTU batteries with a very low self-
discharge.

• 

 NOTE:

 note the specified storage voltage for lithium batteries. Is a completely full or empty lithium battery time stored for a 

longer time, it can be damaged.

The XciteRC Modellbau GmbH & Co. KG cannot monitor the proper use of the battery or batteries you use, therefore, the warranty is 
excluded due to incorrect charging or discharging.

EN

Summary of Contents for 36001000 LEOPARD 2A5

































Reviews: