Xantech PA1235X Installation Instructions Manual Download Page 1

INSTALLATION INSTRUCTIONS 

 

MODEL PA1235X 

12 CHANNEL POWER AMPLIFIER 

 
 
 
 

TABLE OF CONTENTS 

 
 
Section Title 

Page 

 
GENERAL INFORMATION...................................................................................................................................2 
 
PA1235X PANEL AND FEATURE DESCRIPTIONS .............................................................................................3 
 
INSTALLATION  
 

Physical Location And Mounting...............................................................................................................6 

 Connecting 

The 

PA1235X........................................................................................................................7 

 

Stereo Mode Connections........................................................................................................................7 

 Speaker 

Phasing......................................................................................................................................8 

 

Bridged Mode Connections ......................................................................................................................8 

 

Connecting The Remote On/Off Jack .......................................................................................................9 

 

A Typical Multi-Zone System Diagram Using A PA1235X .......................................................................10 

 
TROUBLE SHOOTING ......................................................................................................................................11 
 
SPECIFICATIONS .............................................................................................................................................12 
 
 

Summary of Contents for PA1235X













Reviews: