1. Refer to the setup and operating instructions that came
with the 2.4 GHz Video Receiver, Model VR31A or
VR36A (sold separately) to set up the Receiver.
2. Mount the camera in a suitable location with the antenna
on top so the camera is the right way up. If you install it
outdoors, run the small cable adapter through a hole in
the wall so you can plug the power supply into an AC
outlet indoors.
3. Plug the power supply’s jack into the adapter cable on
the camera.
4. Set the Housecode and Unit Code. (See instructions
included with X10 remote controls).
5. Plug the power supply into any 120V AC outlet.
6. Set the channel switch on the camera to the same setting
as the one on the VR31A or VR36A Video Receiver.
7. Adjust the antenna on the camera if necessary to aim it
in the direction of the VR31A/VR36A Receiver that
you have connected to your TV.
LIMITED 1-YEAR WARRANTY
X10.com, a division of X10 Wireless Technology, Inc. (X10)
warrants X10 products to be free from defective material and
workmanship for a period of one (1) year from the original date of
purchase at retail. X10 agrees to repair or replace, at it’s sole
discretion, a defective X10 product if returned to X10 within the
warranty period and with proof of purchase.
If service is required under this warranty:
Call 1-800-675-3044 or visit www.x10.com, or e-mail
[email protected] to obtain a Return Merchandise Authorization
(RMA) number. Please do not return any products without an
RMA number.
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.
X10.com, a Div. of X10 Wireless Technology, Inc.
For additional help, visit www.x10.com/support
●
Extremely small size.
●
Built-in 2.4 GHz Video Sender.
●
Can be turned on and off remotely (remote controlled power supply included).
●
Use it outdoors to monitor your front door, back yard, etc.
●
Use it indoors to monitor a child’s bedroom, etc.
Model XX16A
XX16A-09/01
The XX16A includes the XC18A camera and XM13A remote controlled power supply. The XC18A is a very small and
compact color video camera with built-in 2.4 GHz transmitter. You can attach it to a wall anywhere you want to monitor. The
XC18A transmits video and sound to the VR31A, or video only to the VR36A receiver which is connected to your TV located
anywhere in your home (up to 100 ft. away). The XM13A power supply lets you turn the camera on and off remotely, from
X10 remote controls (sold separately).
XCam2 InstantON Video Camera
™
F.C.C. CAUTION -
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE:
NO CHANGES OR MODIFICATIONS MAY BE
MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
Point the raised dimple
on the antenna towards
the Receiver’s location.
Plug power
supply in
here.
XC18A
2
5
Plug into
any AC
outlet
Attach
to a wall.
3
Cable adapter.
7
Outdoors
Indoors
Set the code used to
turn on and off from
X10 remote controls.
4
XM13A
6
Set channel switch
(under rubber plug)
to match setting on
VR31A or VR36A
Receiver. (A is at
bottom, D is at top).
It is factory set to A.
Remove clear cap and turn
lens counterclockwise to
focus (replace cap for
outdoor use).
Point backwards from
direction shown here if
you install the camera
outdoors.
