background image

X10 Wireless Technology, Inc. 90 Day Limited Warranty

X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to be 
free from defective material and workmanship for a period of 90 days from the original date 
of purchase at retail. X10 agrees to repair or replace, at it’s sole discretion, a defective X10 
product if returned to X10 within the warranty period and with proof of purchase.

If service is required under this warranty:
1.  Visit www.x10.com/support/return_policy.htm, or e-mail [email protected] to obtain a 

Return Merchandise Authorization (RMA) number.

2.   Return the defective unit postage prepaid to X10 (see address on back).
3.  Enclose a check for $4.00 to cover postage and handling.
4.  Enclose a dated proof of purchase.
5.   X10 is not responsible for shipping damage. Units to be returned should be packed 

carefully.

Please visit www.x10.com/support for help.

TM751-6/13

FCC CAUTION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION 
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE 
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE 
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio frequency energy, and if not installed and used properly, 
that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and 
television reception. It has been type tested and found to comply with the limits for remote control 
devices in accordance with the specifi cations in Sub-Parts B and C of Part 15 of FCC Rules, which 
are designed to provide reasonable protection against such interference in a residential installation. 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause interference to radio or television reception, which can be determined by 
unplugging the equipment, try to correct the interference by one or more of the following measures.

•  Reorient the antenna of the radio/TV experiencing the interference.
•  Relocate the product with respect to the radio/TV.
•  Move the product away from the radio/TV.
•  Plug product into an outlet on a different circuit from the radio/TV experiencing the interference.
•  If necessary, consult your local Dealer for additional suggestions.
 

NOTE: Modifi cations to any of the components in this kit will void the user’s authority to operate 
this equipment.

Trim

Trim

Transceiver Module TM751

INSTALLATION AND OPERATING INSTRUCTIONS

The TM751 Transceiver receives commands from X10 Remote controls and 
turns on a light or appliance connected to its outlet. The Transceiver also 
passes the signals onto your house wiring to control lights, appliances, or 
Wireless Cameras around your home. You plug lights and appliances into 
X10 Modules (sold separately). You plug Wireless Cameras into Addressable 
Power Supplies (sold separately).

1.  Plug the TM751 Transceiver into any 120V AC outlet. Fully extend its 

antenna.

2.  Use a dime to set the Housecode dial on the TM751 to match the X10 

modules, cameras, and remote controls you will be using it with.

3.  Plug a lamp or appliance into the outlet on the TM751 (observe the ratings 

on the back of the TM751).

4.  Press the small button on the TM751 to test that the lamp/appliance goes 

on and off.

5.  Install 4 AAA alkaline batteries in an HR12A PalmPad remote control, 

or CR12A ScanCam remote control (each sold separately).

6.  Press 1 ON and OFF on the remote control to control the light/appliance 

connected to the TM751.

7.  Press the corresponding ON or OFF button  on the remote control to turn 

other X10 Modules or cameras on/off.

Also see instructions included with X10 remote controls and cameras.

For help or more information on setup, please visit 
www.x10.com/support

Print reduced by approx 85%. 
Final size of above =  approx. 7 3/4” x 4 3/4”
Folds into a sheet 3 7/8’ x 2 3/8”
(Like all other instruction sheets)

Reviews: