WYTRON CD-398 Operation Manual Download | Manualshive

Page: 8 / 58

background image

8

3. Installation

You may get

MagicCD

or

MagicDVD

series duplicator in three

possibilities:

A. Controller

only

1.

Prepare necessary devices including:

a.

IDE bus CD/DVD-ROM drive

b.

IDE bus CD/DVD writer.

c.

Suitable tower case.

d. Hard

drive.

e.

Switching power supply (Appropriate capacity is
suggested. Bad quality of power supply might
damage the controller board and cause unstable
operation.

2. Assemble all required devices mentioned above and make

sure all IDE writers are in master mode. The
CD/DVD-ROM reader and hard drive (optional) have to be
connected together at specific slot (black, besides the
power connector) on the controller card with hard drive in
master mode and CD/DVD-ROM in slave. The
CD/DVD-ROM should be connected to the middle
connector of an EIDE cable and the hard drive to the last
connector. If there is only a CD/DVD-ROM or hard drive
installed, the device should be in master mode and be
always connected at the end of the EIDE cable.

Installation profiles are suggested below from left side of
cross-section view. The number of writers installed may
vary due to different controller card and requirements.

«
...
6
7
8
9
10
...
»

Summary of Contents for CD-398



























































Reviews:

No comments

Related manuals for CD-398

Brand: JDS Uniphase Pages: 27

Brand: Danfoss Pages: 20

Brand: OEG Pages: 168

Brand: BADODOSECURITY Pages: 8

Brand: Lamtec Pages: 22

Brand: Polycom Pages: 2

Brand: Baninni Pages: 5

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

Brand: Apricus Pages: 32

Linear Technology ADI Power DC3017A

Brand: Analog Devices Pages: 12

Brand: Samson Pages: 70

Brand: Keysight Technologies Pages: 105

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

Easywave ST01 Series

Brand: Eldat Pages: 2

Brand: GEM Pages: 31

Smart 4 Universal

Brand: Classic Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands