WYTRON CD-398 Page 54 Operation Manual Download

Page: 54 / 58

8. Trouble

shooting

1Q: No display or only black squares on LCD display and the

unit does not boot when power on.

A: Please check the connection of power cable and the

power environment is normal.

B: Please check the fan of power supply. It should rotate if

power-on. If not, the power supply might have problem.

C: Turn off the power of duplicator, open the case to check

whether the power cable is fixed.

2Q: Error message shown on LED:

A: During operation like Copy, Emulate Write, compare and

verify, you may press MODE switch to abort the operation.
An Error message will be shown on the LCD. Some
writers, abort will cause the duplicator to hang up and you
have to re-start the power to return to normal operation.

B: Failed reading may cause the error message shown on

the LCD display. Change the master disc to try again.

C: During operation, if read error, buffer under run or writing

error occurs, the LCD will show error message like: Pass
xx, failed xx.

D: If there is no device connected and detected by duplicator

during power-on, the duplicator will show error message
on LCD before entering the main menu.

3Q: CD/DVD-ROM doesn’t read disc and shows Error

message.

A: Check the master disc for damage.
B: Try to use writer to read the master to see if the master is

defective or simply not compatible with CD/DVD-ROM.

Summary of Contents for CD-398



























































Search results

Summary of Contents for CD-398

Reviews:

Related manuals for CD-398

Brands by name

Popular brands

WYTRON CD-398, Operation Manual

Search results

Summary of Contents for CD-398

Reviews:

Related manuals for CD-398

Brands by name

Popular brands