WWBeds Face Unassembled Alpha Murphy Assembly Instructions Manual Download Page 10 | Manualshive

Page: 10 / 18

WWBeds Face Unassembled Alpha Murphy Assembly Instructions Manual Download Page 10

Assemble the Face

Lock the arm into place

Videos:

and

Frame Bolts and Straps

Caution: If possible have a helper assist in the setting of the mechanism and loading of the bed face panel. DO
NOT reach behind the tension arm when you are doing the setting procedure. To avoid reaching behind the
Tension Arm, use a pencil or screw driver to move the Arm Lock into place.

Holding one foot against the bottom front
edge of the side panel and using the
“Tension Arm Lever Tool”, pull the tension
arm out until you can set the arm lock to
the hex nut at the hole A (see drawing 13.).
This is the hex nut at the top front corner of
the mechanism.

Tip: If you set the “Arm Lock” on top of
the bolt before you pull the Tension
Arm back it will fall into place. Do not
put your fingers back there to while pulling it back!

5-1: Insert a Allen Head Bolts through Hole #1 (This
hole should be the one about 6 3/4” from the end of side
frame) on both left and right side frames (see Drawing).

NOTE: On some Models this Allen Head Bolt may
already be installed.

5-2  On each side, install  5/16“ (M8x20mm) Hex Head
Bolts from the outside of the frame through Hole #3.
Only thread the nut until it is flush with the Nut end.  Do
not tighten.

«
...
8
9
10
11
12
...
»

Summary of Contents for Face Unassembled Alpha Murphy



















Reviews:

No comments