Wulfsberg FLEXCOMM II C-5000 Page 38 Installation Manual Download

Page: 38 / 151

FLEXCOMM

C-5000 (Non-Digital)

Installation Manual

150-1355-000 Rev. M

CONFIDENTIAL AND PROPRIETARY TO COBHAM

Page 38

Installation of Multipin Crimp Connectors

A. Contacts and Crimp Tool Information

Contacts, D-Sub, Min.

Crimp or Solder

WED PN 129-115451-01

Positronic PN FC8122D, crimp (or equivalent) or Positronic

FS8122D, solder (or equivalent)

Crimp Tools

(Suggested supplier:

Daniels

Manufacturing

Corporation

526 Thorpe Road

Orlando, FL 32824)

C-5000 Serial RT Card interface Connector Handle - M22520/2-01

Positioner - M22520/2-08
C-5000 Parallel RT Card Interface Connector

Handle - M22520/2-01 Positioner - M22520/2-06
RT-5000 Interface Connector Tool Frame - M22520/1-01 Turret -

M22520/1-02 Positioner - M22520/2-08

Insertion/Removal

Tool

Positronic M81969/1-04 or equivalent

B. Contacts and Insertion/Removal Tool Manufacturer Name and Address:

Positronic Industries, Inc.

423 N. Campbell Ave.

PO Box 8247

Springfield, Missouri 65801

5. Installation of C-5000
Mount C-5000 on Dzus rails per MIL MS-25213.

See Figure 3-1 for mounting dimensions.

6. Installation of RT-5000

The RT-5000 is should be installed on a horizontal surface in either a horizontal or vertical tray.

However, vertical mounting results in better cooling. Clearance for installing single or dual RT-5000’s is

shown in Figure 3-2a.

(1) Hand-tighten the rack knobs to secure the RT-5000 in the mounting tray. See Figures 3-2

through 3-4 for mounting dimensions.

(2) Attach antenna cabling [Connector J103 (N Type, less-than-or equal-to 400 MHz), and J102

(TNC Type, greater-than-or-equal-to 400 MHz)]. Insure proper connector mating.

(3) Attach RT-5000 mating Connector J101 (55 pin).
(4) Vibration isolators are recommended but not required. Use of isolators (WED P/N 246-

044540-01, quantity 4) is recommended whenever clearance of the RT-5000 is available.

Isolators should only be used with a vertical mounting tray on a horizontal surface. The use

of such isolators is necessary to achieve MIL-STD 810 compliance. For clearance

considerations when mounting an RT-5000 using a Mounting Tray equipped with Vibration

Isolators, see Figure 3-2a.

Summary of Contents for FLEXCOMM II C-5000
























































































































































Search results

Summary of Contents for FLEXCOMM II C-5000

Reviews:

Related manuals for FLEXCOMM II C-5000

Brands by name

Popular brands

Wulfsberg FLEXCOMM II C-5000, Installation Manual

Search results

Summary of Contents for FLEXCOMM II C-5000

Reviews:

Related manuals for FLEXCOMM II C-5000

Brands by name

Popular brands