wtw TresCon UNO A111 Operating Manual Download Page 162

Page: 162 / 208

Maintenance

TresCon UNO

6 - 6

ba43134e08

05/2017

6.1.3

Testing the interfaces

You can send a test string "Test string RS232 (or RS485)" to the selec-
ted interface.

Sending a string

Example Test string

Fig. 6-1

RS485 test string

Measuring mode

Call up the

Service

menu: Simultaneously press the keys,

and

. The request

Enter PIN

appears

Input the PIN digit-by-digit with

. Change the digit

with

and confirm with

. The

Service Mode

menu appears

Select the

RS232

RS485

menu item with

Confirm the selection with

. The test string is sent to the

selected interface. A confirmation appears on the display.

------------------------------------------------------------
RS485 test string
------------------------------------------------------------
TresCon>

Summary of Contents for TresCon UNO A111
















































































































































































































Search results

Summary of Contents for TresCon UNO A111

Reviews:

Brands by name

Popular brands

wtw TresCon UNO A111, Operating Manual

Search results

Summary of Contents for TresCon UNO A111

Reviews:

Brands by name

Popular brands