wtw TresCon UNO A111 Operating Manual Download Page 152

Page: 152 / 208

Operation

TresCon UNO

5 - 96

ba43134e08

05/2017

5.9

Permeate switch

General

With the aid of the TC/ PU1 permeate switch you can alternately mea-
sure two different samples (permeates) with one analyzer module.

Note

How to install the TC/ PU1 permeate switch is described in section
3.7.1 from page 3-30.

How it functions

Fig. 5-25 Principle of the permeate switch for an analyzer module

With the aid of an electrically switchable three/two way valve the ana-
lyzer module is alternately connected to one of the two overflow ves-
sels of the permeate switch. The three/two way valve is controlled by
the TresCon controller.

TresCon analyzer module

3/2-Way valve

Overflow vessel 2

Overflow vessel 1

Sample 2

Sample 1

erflo

ent

Terminal strip

TresCon

V1/V2/V3

Summary of Contents for TresCon UNO A111
















































































































































































































Search results

Summary of Contents for TresCon UNO A111

Reviews:

Brands by name

Popular brands

wtw TresCon UNO A111, Operating Manual

Search results

Summary of Contents for TresCon UNO A111

Reviews:

Brands by name

Popular brands