wtw pHotoFlex STD Manual Download Page 55

Page: 55 / 80

pHotoFlex

STD

Operation

ba75958e07

11/2020

4.9

Meter information

The following meter information is listed in the

Configuration

Info

menu:



Model designation



Software version



Version number(s) of the stored program data



Series number of the meter

4.10

Software update

With a software update you obtain the current software with all new programs
and method data (see section 11).

A software update comprises



new instrument software



new programs (methods)



revisions of existing methods

The current software version can be found on the Internet at

www.WTW.com

The proceeding for updating the software is given in the appendix (see
section 11).

Model

: pHotoFlex

Software

: V 1.70

Prog.

V 1.24 W

Ser. no.

12345678

Info

Summary of Contents for pHotoFlex STD
















































































Search results

Summary of Contents for pHotoFlex STD

Reviews:

Related manuals for pHotoFlex STD

Brands by name

Popular brands

wtw pHotoFlex STD, Manual

Search results

Summary of Contents for pHotoFlex STD

Reviews:

Related manuals for pHotoFlex STD

Brands by name

Popular brands