wtw pHotoFlex STD Manual Download Page 46

Page: 46 / 80

Operation

pHotoFlex

STD

ba75958e07

11/2020

4.6.2

Filtering measurement datasets

The functions to display and download stored measurement datasets (see
section 4.4.1) refer to all stored measurement datasets that correspond to
the specified filter criteria.

The settings are in the menu,

Configuration

System

Measured value mem-

ory

Data filter

Move to the

Configuration

menu with the

<MENU>

key.

Data filter

Menu item

Setting/function

Explanation

Filter

Filter criteria:

No filter

Data filter switched off

Selection according to ID num-
ber

PROG

Selection according to program

Date

Selection according to period

ID + PROG

Selection according to program
and ID number

ID + Date

Selection according to period
and ID number

PROG + Date

Selection according to program
and date

ID + PROG + Date

Selection according to ID, pro-
gram and date

Entry of filter criteria

These menu items are made vis-
ible by selecting the filter criteria
in the

Filter

menu.

PROG

Date

Summary of Contents for pHotoFlex STD
















































































Search results

Summary of Contents for pHotoFlex STD

Reviews:

Related manuals for pHotoFlex STD

Brands by name

Popular brands

wtw pHotoFlex STD, Manual

Search results

Summary of Contents for pHotoFlex STD

Reviews:

Related manuals for pHotoFlex STD

Brands by name

Popular brands