wsm Kubota L4100 Workshop Manual Download

Page: 40 / 346

GENERAL

L4100, WSM

G-25

(EU)

Cleaning Fuel Filter

This job should not be done in the field, but in a clean place.

1. Close the fuel cock (1).
2. Unscrew the screw ring (6), remove the filter bowl (5), and rinse

the inside with kerosene.

3. Take out the element and dip it in the kerosene to rinse.
4. After cleaning, reassemble the fuel filter, keeping out dust and

dirt.

5. Bleed the fuel system. (See page G-33.)

9Y1210278GEG0024US0

Adjusting Parking Brake Lever

CAUTION

• Stop the engine and chock the wheels before checking

parking brake.

1. Raise the parking brake lever to the parking position while

counting the ratchet sound made by the parking brake lever.

2. If adjustment is needed, loosen the lock nut (2) and adjust the

parking brake cable (1) length with in acceptable limit.

3. Retighten the lock nut (2).

9Y1210278GEG0025US0

Adjusting Clutch Pedal Free Travel

• Refer to G-15.

9Y1210278GEG0026US0

(1) Fuel Cock
(2) O-ring
(3) Filter Element
(4) Spring

(5) Filter Bowl
(6) Screw Ring

(A) "CLOSE"
(B) "OPEN"

Proper parking brake lever free travel

1 notch (Ratchet sound 1)

(1) Parking Brake Cable

(2) Lock Nut

KiSC issued 08, 2012 A

Summary of Contents for Kubota L4100



























































































































































































































































































































































Search results

Summary of Contents for Kubota L4100

Reviews:

Related manuals for Kubota L4100

Brands by name

Popular brands

wsm Kubota L4100, Workshop Manual

Search results

Summary of Contents for Kubota L4100

Reviews:

Related manuals for Kubota L4100

Brands by name

Popular brands