wsm Kubota L4100 Workshop Manual Download | Manualshive

Page: 192 / 346

background image

TRANSMISSION

L4100, WSM

3-S29

(EU)

(Continued)

4. Remove Lo-reverse gear shaft assembly (4).
5. Remove Lo-reverse fork rod (3), front wheel drive shift lever (5).

9Y1210278TRS0026US0

Differential Lock Shift Fork

1. Tap out the left side spring pin (4).
2. Remove the cotter pin and take out the clevis pin (3).
3. Draw out the differential lock fork shaft (1) and take out the

differential lock shift fork (2).

(When reassembling)

• Apply grease to the left and right oil seals on the transmission

case.

• Insert the clevis pin (3) form the top and install the washer and

cotter pin.

• Tap in the spring pin (4) so that its split portion a may face

outward as shown in the figure.

9Y1210278TRS0027US0

(1) Hi-shift Fork Rod
(2) Pinion Gear Shaft Assembly
(3) Lo-reverse Fork Rod
(4) Lo-reverse Gear Shaft Assembly

(5) Front Wheel Drive Shift Lever
(6) PTO Gear Shaft Assembly
(7) Front Wheel Drive Gear Shaft

Assembly

(1) Differential Lock Fork Shaft
(2) DIfferential Lock Shift Fork
(3) Clevis Pin
(4) Spring Pin

a: Split

Portion

KiSC issued 08, 2012 A

«
...
190
191
192
193
194
...
»

Summary of Contents for Kubota L4100



























































































































































































































































































































































Reviews:

No comments

Related manuals for Kubota L4100

Brand: Vari Pages: 44

Brand: New Holland Pages: 41

Brand: Vaughan Pages: 4

REV. 1000 E (2+2)

Brand: S.E.P. Pages: 32

Brand: Cub Cadet Pages: 61

Brand: Jacobsen Pages: 86

Brand: Jenn-Air Pages: 4

Brand: MASSEY FERGUSON Pages: 41

Brand: Thwaites Pages: 28

Brand: ROTOTILT Pages: 8

Sportsman Touring 570 EPS 2021

Brand: Polaris Pages: 186

Brand: Harvest TEC Pages: 20

Brand: Full Boar Pages: 17

Brand: Agri-Fab Pages: 24

Brand: Mitsubishi Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands