background image

 

TST-019 MRTALPCH CHANNEL 

– Rev. 2016-310 

Page 13 of 20 

 

39)   Disconnect the two hoses, one red and one 

green, from the Y-fitting that connect to the 
vacuum tanks, taking care to not damage the 
fitting barbs.  Examine the barbs of the Y-fitting to 
determine if there are any large nicks in the barbs 
that could allow a hose to leak.  If the barbs are 
not damaged, cap off the barbs as shown in 

FIGURE 18

40)   With the ball valve in the open position (handle in 

line with the valve), switch the power on 

(    )

, and 

activate the vacuum generating system by 

pressing the apply 

(    )

 push button. 

41)   Close the ball valve (turn handle perpendicular to the valve), switch the power to off 

(    )

 and 

observe the vacuum gauge of the ball valve. 

  If the vacuum level, 

as shown on the ball valve’s vacuum gauge, starts and continues to 

drop, the indication is that the Y-fitting leaks.  Replace the Y-fitting.  Reconnect the hoses 
and confirm by repeating the test shown in 

FIGURE 7

.  If the leak continues, proceed to next 

step to test the individual tank lines. 

 

If the vacuum level of the ball valve’s vacuum gauge holds steady and does not drop, the 
indication is that one or both of the hoses connected to the vacuum tanks is the cause of the 
leak.  Proceed as follows. 

42)   Remove one of the caps from either barb of the Y-fitting and reconnect one tank line. 

FIGURE 19

 shows how to test either the red or green tank lines. 

43)   With the ball valve in the open position (handle in line with the valve), switch the power on       

(    )

, and activate the vacuum generating system by pressing the apply 

(    )

 push button. 

 

 

FIGURE 19 

 

FIGURE 18 

Summary of Contents for MRTALPCH611LDC
























Reviews: