background image

6

2. sAfetY precAutIons

 Do not operate the generator near gasoline or gaseous fuel because of the potential 

danger of explosion or fire.

 Do not fill the fuel tank with fuel while the engine is running. Do not smoke 

or use a naked flame near the fuel tank. Be careful not to spill fuel during 

refueling. If fuel is spilt, wipe it off and let dry before starting the engine.

 Do not place inflammable near the generator. Be careful not to place fuel, matches, gunpowder, 

oily cloths, straw, trash, or any other in flammables near the generator.

 Do not operate the generator inside a room, cave, tunnel, or other insufficiently ventilated area. 

Always  operate  it  in  a  well-ventilated  area,  otherwise  the  engine  may 

become  overheated,  and  the  poisonous  carbon  monoxide  gas  contained 

in  the  exhaust  gases  will  endanger  human  lives.  Keep  the  generator  at 

least  1  meter  (3  feet)  away  from  any  structure  or  building  during  use.  If 

the generator must be used indoors, the area must be well-ventilated and 

extreme caution must be taken regarding the discharge of exhaust gases. Failure to follow the 

correct procedures can be fatal.

 Do not enclose the generator nor cover it with a box. The generator has a built-in forced air cooling 

system, and may become overheated if it is enclosed. If generator has been covered to protect it 

from the weather during non use, be sure to remove it and keep it well away from the area during 

generator use.

 Operate the generator on a level surface. It is not necessary to prepare a special foundation for 

the generator. However, the generator will vibrate on an irregular surface, so choose a level place 

without surface irregularities. If the generator is tilted or moved during operation, fuel may spill 

and/ or the generator may tip over, causing a hazardous situation. Proper lubrication cannot be 

expected if the generator is operated on a steep incline or slope. In such a case, piston seizure 

may occur even if the oil level is above the minimum level.

 Pay attention to the wiring or extension cords from the generator to the connected 

device. If the wire is under the generator or in contact with a vibrating part, it may 

break  and  possibly  cause  a  fire,  generator  burnout,  or  electric  shock  hazard. 

Replace damaged or worn cords immediately.

 Do not operate in rain, in wet or damp conditions, or with wet hands. The operator may suffer 

severe electric shock if the generator is wet due to rain or snow.

 If the generator is wet, wipe and dry it before starting. Do not pour water directly over the generator, 

never wash it with water.

Summary of Contents for SILENTSTAR 11000D M AVR YN





























Reviews: