background image

14

• 

Make sure you review each warning in order to prevent fire hazard. 

• 

Keep area clear of in flammables or other hazardous materials. 

• 

Keep generator at least 3 feet (1 meter) away from buildings or other structures. 

• 

Only operate generator in a dry, well ventilated area. 

• 

Keep exhaust pipe clear of foreign objects.

• 

Keep generator away from naked flame. No smoking! 

• 

Keep generator on a stable and level surface.

• 

Do not block generator air vents with paper or other material.

GrounDInG the GenerAtor

• 

Before using the generator, the grounding lug on the panel 

must be connected to the earth.

• 

To  ground  the  generator  to  the  earth,  connect  the 

grounding  lug  of  the  generator  to  the  grounding  spike 

driven into the earth or to the conductor which has been 

already grounded to the earth.

• 

If  such  grounding  conductor  or  grounding  electrode  is 

unavailable,  connect  the  grounding  lug  of  the  generator 

to  the  grounding  terminal  of  the  using  electric  tool  or 

appliance.

Earth Terminal

6. operAtInG proceDures

Before starting the generator:

• 

Check the oil level as explained before page 10. Do never  move the accelerator 

lever adjusted in the manufactured plant

• 

Check the gasoline pipes are drained of the air bubble.

6.1. stArtInG the enGIne

note

All the information related to the display is written in the manual user book.

Summary of Contents for SILENTSTAR 11000D M AVR YN





























Reviews: