Worldlawn WYW36FS481VH Operator'S Manual Download Page 21

 

 

HYDRO-DRIVE WALK BEHIND MOWER 

 

 

 

 

21

 

 

PRE-START 

Fill fuel tank on level ground.  For best results 
use only clean, fresh regular grade unleaded 
gasoline with an octane rating of 87 or higher. 

IMPORTANT:  Never use methanol, gasoline 
containing methanol, gasohol containing 
more than 10% ethanol, premium gasoline, 
or white gas because the fuel system could 
be damaged. 

Do Not

 add oil to gasoline 

Do Not

 over fill fuel tank.  Fill the fuel tank to 

the bottom of the filler neck.  The empty space 
in the tank allows gasoline to expand.  
Overfilling may result in fuel leakage or damage 
to the engine or emission system.  

Make sure you understand the controls, their 
locations, their functions, and their safety 
requirements. 

Refer to the Maintenance section and perform 
all the necessary inspection and maintenance 
steps. 

OPERATING

 

INSTRUCTIONS 

STARTING THE ENGINE 

1.  Move the speed control lever to the neutral 

position. 

2.  Move the park brake lever to the on 

position. 

3.  Push in (down) on the PTO switch to the 

“disengage” position. 

4.  Place the throttle midway between the 

“SLOW” and “FAST” positions. 

5.  On a cold engine, pull the choke knob up 

into the “ON” position. 

6.  On a warm engine, leave the choke in the 

“OFF” position. 

7.  Turn 

ignition switch to the “ON” position. 

8.  Give the recoil starter a few quick pulls to 

start the engine. 

9. 

If the choke is in the “ON” position, 
gradually return choke to the “OFF” position 
as the engine warms up. 

BLADE ENGAGEMENT 

DANGER 

The rotating blades under the mower deck 
are dangerous.  Blade contact can cause 
serious injury or kill you. 

Do Not put hands or feet under the mower 
or mower deck when the blades are 
engaged. 

DANGER 

An uncovered discharge opening will allow 
objects to be thrown in an operator’s or 
bystander’s direction.  Also, contact with 
the blade could occur.  Thrown objects or 
blade contact can cause serious injury or 
death. 

Summary of Contents for WYW36FS481VH









































Reviews: