Worldcast Systems ECRESO FM 10kW, User Manual

Page: 105 / 243

ECRESO FM 5kW / 10kW, user manual – 11/2021
Page 105
WorldCast Systems SAS - 20 avenue Neil Armstrong - 33700 Mérignac (Bordeaux Métropole) FRANCE
+33 (0)5 57 928 928
– www.worldcastsystems.com – contact@worldcastsystems.com
NAME
Access
(R/W)
Possible value on the serial
port of the unit
Comments Module
SYS.SDC.FAULT R
"OK" or "FAULT"
Failed = read/write error on the µSD card ECU | DRVn
SYS.SDC.STATE R
"MOUNT" or "UNMOUNT"
Gives the status of the µSD card. The state must
be UNMOUNT before the card can be removed. ECU | DRVn |
PAn | PSUn
SYS.SDC.PRES R
"PRES" or "NOT PRES"
Indicates whether a µSD card is present ECU
SYS.SN R YYMMXXXX A,M,X=[0..9]
Serial number of the unit: Y => year, M => month,
X => number
ECU
SYS.SOFTREL R xx.xx.xx x=[0..9] Software version: example "3.0.1"
ECU | DRVn |
PAn
SYS.SOFTREL.LIST R xx.xx.xx x=[0..9]
List of the exciter software versions
CPU;DSP;FPGA;IP;EXC;A/IP;TUN
ECU | DRVn
SYS.TIME R/W HH:MM:SS Reads and sets the amplifier time ECU
SYS.TYPE R xxx x=[A..Z;0..9] Unit type. ECU
SYS.UNIT R/W
"ABSOLUTE" or "PERCENT"
or "RELATIVE"
Input method for audio silence detection
threshold. It is used for commands
INPUT.xxx.SW.THRESH; default value: RELATIVE
ECU
SYS.UPTIME R [0..99999999]
Indicates the number of working hours since
commissioning
ECU
7.2.2. Measurement commands
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments Module
MEAS.5V R xx.x x=[0..9] Measures the 5 V voltage ECU | DRVn
MEAS.12V R xx.x x=[0..9] Measures the 12 V voltage ECU | DRVn
MEAS.24V R xx.x x=[0..9] Measures the 24 V voltage ECU
MEAS.AMB R ±[0..125]
Measures the ambient temperature from 0 to
125°C. "52"=>52°C. ECU | DRVn | PAn |
PSUn
MEAS.CLIP R
"ON" or "OFF" Status of the hard limiter
ECU | DRVn
MEAS.CUR1 R xxx.x x=[0..9]
Measures the power supply 1 current.
Examples: "02.0"=>2 A "15.2"=> 15.2 A
DRVn | PAn | PSUn
MEAS.CUR2 R xxx.x x=[0..9]
Measures the power supply 2 current.
Examples: "02.0"=>2 A "15.2"=> 15.2 A (1500
& 2000 W modules only)
PAn | PSUn
MEAS.CUR4 R xxx.x x=[0..9]
Measures the power supply 4 current.
Examples: "02.0"=>2 A "15.2"=> 15.2 A (1500
& 2000 W modules only)
ECU
MEAS.DEV.PEAK R - 150,0…150,0
Gives the peak value for the signal deviation
in kHz
ECU | DRVn
MEAS.DEV.PKMAX R - 150.0…150.0
Gives the peak value for the signal deviation
in kHz over 1 second
ECU | DRVn
MEAS.DEV.RMS R - 150.0…150.0
Gives the average value for the signal
deviation in kHz
ECU | DRVn
MEAS.EXC_TEMP R ±[0..125]
Gives the temperature of the modulator
board
DRVn
MEAS.FAN1.SPEED R xxx.x x=[0..9] Fan 1 speed in RPM ECU | DRVn | PSUn
MEAS.FAN2.SPEED R xxx.x x=[0..9] Fan 2 speed in RPM ECU | PSUn
MEAS.FAN3.SPEED R xxx.x x=[0..9] Fan 3 speed in RPM ECU
MEAS.FAN4.SPEED R xxx.x x=[0..9] Fan 4 speed in RPM ECU
MEAS.HEAT1 R ±[0..125]
Measures the
heatsink
1 temperature
DRVn | PAn | PSUn
MEAS.HEAT2 R ±[0..125]
Measures the
heatsink
2 temperature
PAn | PSUn