background image

— GENERAL INFORMATION

— WARRANTY / PARTS / SERVICE

— OPERATION

WARNING: 

Some chemicals will damage the pump valves if allowed to soak untreated for a long period of time. 

Always flush the pump with water after use. Do not allow chemicals to sit in pump for extended times of idleness.

Follow chemical manufacturers instructions on disposal of all waste water from the sprayer.

— AFTER SPRAYING

— WINTER STORAGE

25 & 15 GAL. ECONOMY SPOT SPRAYER

MODEL # LG25 ESS and LG15 ESS

Products are warranted for one year from date of purchase against 

manufacturer or workmanship defects.

Your authorized dealer is the best source of replacement parts and 

service. To obtain prompt, efficient service, always remember to give 

the following information:

 

1) Correct part description and part number.

 

2) Model number of your sprayer.

Part description and part numbers can be obtained from the 

illustrated parts list section of this manual.

Whenever you need parts or repair service, contact your distributor / 

dealer first. For warranty work always take your original sales slip, or 

other evidence of purchase date, to your distributor / dealer.

The pumping system draws solution from the tank, through the 

strainer and to the pump. The pump forces the solution under 

pressure to the spray wand.

The pump has a pressure switch which will shut the pump off when it 

reaches 40 PSI.

Regularly inspect the suction supply screen on the inside of the tank. 

Flush with water to clear any accumulated debris.

*These sprayers are designed to be attached to a stable surface.

The purpose of this manual is to assist you in assembling, operating 

and maintaining your lawn and garden sprayer.

Please read it carefully as it furnishes information which will help you 

achieve years of dependable trouble-free operation. 

After use, fill the sprayer part way with water. Start the sprayer and 

allow clear water to be pumped through the plumbing system and out 

through the spray wand.

Refill the tank about half full with plain water and use a chemical 

neutralizer such as Nutra-Sol® or equivalent and repeat cleaning 

instructions. Flush the entire sprayer with the neutralizing agent. 

Follow the chemical manufacturer’s disposal instructions of all wash 

or rinsing water.

Drain all water and chemical out of sprayer, paying special attention 

to pump and valves. These items are especially prone to damage 

from chemicals and freezing weather.

The sprayer should be winterized before storage by pumping a 

solution of RV antifreeze through the entire plumbing. Proper care 

and maintenance will prolong the life of the sprayer.

• Polyethylene Tank

• 12 Volt Diaphragm Pump

• 1.0 G.P.M.

• Lever Handgun

• 15 Ft. of 3/8” Hose (Handgun)

Assembly / Operation Instructions / Parts

LG15 ESS

LG25 ESS

PRECISION SPRAY EQUIPMENT, a divison of Green Leaf, Inc.   9490 N BALDWIN ST   FONTANET, IN 47851   www.grnleafinc.com   800-654-9808

a division of Green Leaf, Inc

®

P R E C I S I O N   S P R AY   E Q U I P M E N T

PSE

®

WORKHORSE

WORKHORSE

S   P   R   A   Y   E   R   S

by PSE®, a Division of Green Leaf, Inc®

by PSE®, a Division of Green Leaf, Inc®

®

Summary of Contents for LG25 ESS

Page 1: ...Flush with water to clear any accumulated debris These sprayers are designed to be attached to a stable surface The purpose of this manual is to assist you in assembling operating and maintaining your lawn and garden sprayer Please read it carefully as it furnishes information which will help you achieve years of dependable trouble free operation After use fill the sprayer part way with water Star...

Page 2: ...er Assembly 600155 1 7 8 Spray Wand Clip 600151 2 18 5 mm Diameter Pinch Clamp 600149 3 9 Lead Wire Assy w Switch 96 600153 1 10 10 24 3 8 Pan 600152 2 11 Rubber Grommet 600207 1 12 15 Gallon Tank 600239 1 13 Economy Wand Hose Assembly 600261 1 14 1 0 GPM Pump w Barbed Fittings 630011 1 15 10 24 x 3 4 Truss Head Screw 630014 4 16 PRECISION SPRAY EQUIPMENT a divison of Green Leaf Inc 9490 N BALDWIN...

Page 3: ...ners Stainless steel and zinc plated Pressure Flow Amp Draw PSI Bar GPM LPM Amps 0 3 0 2 1 00 3 7 1 5 10 0 7 0 85 3 1 1 9 20 1 4 0 71 2 6 2 1 30 2 1 0 61 2 3 2 4 40 2 8 0 42 1 6 2 6 Parts List Ref Part Description Number 1 Switch Asssembly 5157201 2 Pump Head wSwitch Asssembly 5275064 3 Motor with connector no switch P39 045B Dimensions Inches mm 2 25 57 6 89 175 1 66 42 2 55 65 3 94 100 1 58 40 1...

Page 4: ...ine fuse and or fuse in car adapter end Ensure correct voltage 10 12 13 volt Low flow or no flow at all what should I check Check for a clogged suction hose and or suction strainer Often you will need to clean the suction strainer Check for proper voltage Is there a fuse for the sprayer Yes either an in line fuse a fuse located in the car adapter housing or both What size fuse should I use as a re...

Reviews: