Worcester Greenstar Oilfit Flexi CF Flue Installation Instructions Manual Download Page 3

Product information

3

Greenstar Oilfit Flexi CF Flue – 6720807911 2019/05

H

Danger of death from poisoning by flue gas due 
to inadequate combustion

Danger of death due to flue gas leak. If flues are 
damaged or leaking, or if you smell flue gas, observe 
the following rules.

▶ Close the fuel infeed.
▶ Open doors and windows.
▶ If necessary, warn all residents and leave the 

building.

▶ Prevent third parties from entering the building. 
▶ Rectify any damage to the flue gas pipe 

immediately.

▶ Check the combustion air supply.
▶ Do not cover or reduce the size of ventilation 

openings in doors, windows and walls.

▶ Ensure that there is adequate combustion air 

supply, including for any appliances installed at a 
later date, e.g. extractor fans, kitchen fans or air 
conditioning units that discharge air to the outside.

▶ Never operate the device if there is insufficient 

combustion air supply.

H

Electrical work

Electrical work must only be carried out by electrical 
installation contractors.

Before starting electrical work:
▶ Isolate all poles of the mains voltage and secure 

against reconnection.

▶ Make sure the mains voltage is disconnected.
▶ Observe the wiring diagrams of other system 

components as well.

H

 Packaging

The following points should be observed during 
unpacking.
▶ Check the delivery immediately upon receipt for 

completeness and possible transport damage.

▶ In the event of transport damage, the delivery 

should only be accepted conditionally.

▶ Do not use damaged components for assembly.
▶ Carefully unpack the unit.
▶ Ensure that all packaging material is removed and 

that the unit is free from all materials that may 
prevent the unit from operating correctly.

1.3

Requirements

Installation

The flue installation must be fitted and terminated in accordance with 
your local regulations.

Support

Flues require adequate support throughout their entire run.

Flue System

Only use the approved Oilfit flue system accessories with this flue kit.

Replacing an existing flue

When replacing an existing Oilfit flue on an appliance:
▶ Ensure it is the correct flue system for the appliance as we have 

various flue systems for Floor Standing oil appliances.

▶ Ensure the flue installation meets current Building Regulation 

requirements.
– Building Regulation requirements may have changed from the 

original date of installation of the existing flue system.

Annual inspection

When the flue system is inspected during the annual service, the 
engineer must inspect and confirm that:
▶ The flue system is continuous without any breaks.
▶ All joints in the flue system are secure and correctly assembled 

according to the manufacturers instructions.

▶ The flue has a fall of 3° (52 millimetres per metre) back to the boiler.
▶ The terminal is not damaged or restricted.
▶ The plume management kit is not damaged (if fitted).

2

Product information

Conventional flexible flue liner

For use with the following Worcester Greenstar oil-fired appliances:

Utility 18/25, 32/50, 50/70

Danesmoor 18/25

Heatslave 12/18, 18/25, 25/32

Camray Kitchen 12/18, 18/25, 25/32

Camray Utility 12/18, 18/25, 25/32

Camray Utility System 12/18, 18/25, 25/32

Heatslave II 12/18, 18/25, 25/32

Danesmoor (2013) 12/18, 18/25, 25/32

Summary of Contents for Greenstar Oilfit Flexi CF Flue

















Reviews: