manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 62

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 62/79 

© Woodward 

Generator Overload Monitoring 

Generator real power is monitored to ensure it does not exceed a preset limit. The watchdog assigned to this relay 
is at terminals 37/38. The relay contact is a N.O. contact. When operating in normal operations the relay is con-
tinuously energized. If the monitored values leave the configured range, the relay will de-energize, the contact 
will open, and the message "Gen. overload" will be displayed. If the fault conditions exist for less than 1 second, 
the relay returns to normal operations. The fault message on the display may be cleared automatically or by 
pressing the ""Clear" button (see chapter Auto Acknowledge Messages at page 64). 
 

Gen. overload 
Monitoring  ON   

Overload monitoring 

ON / OFF 

ON

................Monitoring of generator real power for overload is performed. The 

following screens of this function are displayed. 

OFF

..............There is no real power overload monitoring and the following 

screens of this function are not displayed. 

 

Gen. overload 
Threshold =000% 

Generator overload threshold 

0 to 150 % 

The threshold value refers to the configured generator rated power. 

 

Gen. overload 
Delay time = 00s 

Generator overload monitoring delay 

0 to 99 s 

The generator real power must remain above the threshold value without interrup-
tion for at least the period of time specified in this screen for a fault condition to be 
recognized. If 0 seconds if configured here, the delay time is approximately 80ms. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands