manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 52

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 52/79 

© Woodward 

Real Power Controller 

 

Power controller 
           ON   

Real power controller 

ON/OFF 

ON

................During mains/parallel operation the real power is controlled to the 

pre-selected set point value. The following screens of this option are 
displayed. 

OFF

..............The power is not controlled, and the following screens of this option 

not displayed. 

Power Limitation 

Power controller 
P max.=    000 % 

Maximum power limitation (maximum demand) 

10 to 120 % 

If limiting control of the generator maximum real power is required, a value in per-
cent referring to the generator rated power is set in this screen. The value "Pmax" 
limits only the set value of the real power controller and has no function in isolated 
operation. 

 

Power controller 
P min.=    000 % 

Minimum power limitation (minimum power) 

0 to 50 % 

If limiting control of the generator minimum real power is required, a value in per-
cent referring to the generator rated power is set in this screen. The value "Pmin" 
limits only the set value of the real power controller and has no function in isolated 
operation. 

Part Load Lead 

Warm up load 
Set point = 000 
% 

Limit value partial load 

5 to 110 % 

If the engine requires a warming-up period a lower fixed power set point value can 
be specified. The limit value of partial load refers to the generator rated power. 

 

Warm up load  
time       000s 

Period of partial load limit 

0 to 600 s 

If a warm up load set point value has been selected, the time period for this warm 
up is configured in this parameter. The time period for the partial load imitates at 
the closing of the generator circuit breaker. If a warm up period is not desired, enter 
"0" for this parameter. 

Shut Down 

Download and 
open GCB     ON 

Shut down 

ON / OFF 

ON

................The generator set will shut down if the input "enable GCB" is re-

moved.  

OFF

..............If "enable GCB" is removed, the CB will not be opened in isolated 

operation. In parallel isolated operation the generator CB remains 
closed. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands