manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 50

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 50/79 

© Woodward 

Volt. controller 
Derivat.Tv=0.00s 

SPM-D11/LSXR 

'ANALOG' 

Voltage controller - derivative-action time 

0.00 to 6.00 s 

The derivative-action time TV represents the D-component of the PID controller. 
The D-component of the controller output becomes effective with large variations 
of the offset, e.g. in case of load-shedding. The lower the derivative-action time is 
configured, the higher the controller reaction is. If TV is configured as 0.00 s, the 
D-component of the PID loop is disabled. Refer to "Analog Controller Outputs" on 
page 29. 

 

Power Factor Control 

 

Pow.fact.control 
           ON   

Power factor controller 

ON/OFF 

ON

................A load-independent control of the power 

ϕ

 factor is carried out dur-

ing mains/parallel operation. The power factor cannot be measured 
accurately and the controller is automatically locked to prevent insta-
bility when small currents (less than 5 % of the CT secondary rated 
current) are detected. The following screen masks of this option will 
be displayed. 

OFF

..............The frequency is not controlled, and the following screens of this op-

tion will not be displayed. 

 

Pow.fact.control 
Set point = 0.00 

Power factor controller set point 

i0.70 to 1.00 to k0.70 

While operating in a mains/parallel operation, the reactive load is controlled so that 
this preset power factor is maintained when the generator is in a steady state. The 
letters "i" stands for "inductive = lagging" (overexcited generator) and "c" for "ca-
pacitive = leading" (underexcited generator) reactive load. This parameter is only 
enabled when operating in mains/parallel. 

 

Pow.fact.control 
Ramp      0.00/s 

Set point ramp of the power factor controller 

0.01 to 0.30 /s 

The set point ramp determines how fast the power factor set point approaches its 
target value. The slope of the ramp is linear. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands