manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 40

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 40/79 

© Woodward 

Direct Configuration 

 

 

NOTE

 

To carry out direct configuration, you require a direct configuration cable (Part #5417-557), the LeoPC 1 
program (supplied with the cable), and the corresponding configuration files. Please consult the online 
help installed when the program is installed for a description of the LeoPC 1 PC program and its setup. 

 
 
Direct configuration permits the user to display the control’s parameters at any time. If the password protection is 
disabled or the control has had the code level 2 access code entered, the user may change all of the parameters 
via direct configuration. If the password protection has been enabled or the control has access code levels 0 or 1 
entered, the access code for code level 2 must be entered via direct configuration, to modify any of the parame-
ters. The ability to modify parameters through the display is not affected. 
 
 

Direct para. 
           YES 

Configuration via the programming jack 

YES/NO 

YES

..............Configuration via the DPC cable is possible. The following addi-

tional conditions must be met: 
-  A connection between the control and the PC via the direct 
configuration cable must be available 
-  the baud rate of the LeoPC program must be 9.600 Baud 
-  the corresponding configuration file (filename: "*.cfg" and 
"*.asm") must be installed properly in the LeoPC1 program being 
used. 

NO

................Configuration via programming plug cannot be carried out. 

 
 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands