manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 38

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 38/79 

© Woodward 

Chapter 6. 

Configuration 

 

 
 

 

CAUTION

 

Please note that configuration should not be carried out while the control unit is in operation. 

 
 

 

NOTE

 

A list of parameters may be found in Appendix B in this manual. 

 
 
The configuration mode will be enabled through the front face panel by simultaneously pressing the "Digit

↑

" and 

"Cursor

→

" buttons. The user may advance through the configuration screens by pressing the "Select" button. 

Pressing and holding the "Select" button will enable the "AUTOSCROLL" function, permitting the user to rap-
idly advance through the configuration screens. Note that it is possible to back up to previous configuration 
screens, but the user may only move back up to four (4) screens and cannot back up from the first configuration 
screen to the last configuration screen. If the controller is left idle for 10 minutes, the controller automatically re-
turns to the automatic mode. 

Basic Data 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

 

 

SPRACHE/LANGUAGE 
---------------- 

Language selection 

English / German 

The desired language for the controller to operate in is set by this parameter. The 
screens (configuration and display screens) can be displayed either in German or 
English. 

 

Software version 
     x.xxxx      

Software version 

Indicates the software version currently installed. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands