manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 37

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 37/79 

LC Display 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

 

 

15

 

LC-Display 

LC-Display 

Performance values can be monitored from the two-line display, pro-
vided that the control is in automatic mode. In configuration mode, 
the individual parameters are displayed. 

Display Monitoring in Automatic Mode: Double Voltage / Frequency Display 

LCD type 1 

(V configured) 

B: 000 V 00.00Hz 
G: 000 V 00.00Hz 

 

LCD type 2 

(kV configured) 

B:00,0kV 00.00Hz 
G:00,0kV 00.00Hz 

Double voltage and double frequency displays, Generator values 

The generator and synchronization voltage and -frequency are displayed. The phase 
angle between the generator and synchronization voltage is displayed by the syn-
chroscope (LED strip). 
 

B

........Synchronization voltage and frequency 

G

.......Generator voltage and frequency 

 

LCD type 1 

(V configured) 

Gen  000V  i0.95 
     000A  000kW 

 

LCD type 2 

(V configured) 

Gen 00,0kV i0.95 
     000A  000MW 

Generator values 

Generator values are monitored: 
 

G

.......Generator values 

 

•

 upper line: 

    - Line voltage L1-L2 
    - phase angle 

•

 bottom line: 

    - current L1 
    - Real power 

Display Monitoring in Automatic Mode: Alarm Indication 

---------------- 
xxxxxxxxxxxxxxxx 

Alarm indication, bottom line 

The indications are displayed according to the following list: 

 

Type of alarm 

Displayed text 

Synchronization time is exceeded 

Synchr. time

 

Wire break 0/4-20mA input for set point value 

Wirebreak P

 

set.

Generator underfrequency 

Gen. underfrequency. 

Generator overfrequency 

Gen. overfrequency. 

Generator undervoltage 

Gen.undervoltage. 

Generator overvoltage 

Gen.overvoltage. 

Generator overload 

Gen.overload. 

Generator reverse-/-reduced load 

Reverse/reduced load. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands