Woodley Clinispin Horizon 6 Flex Operator'S Manual Download Page 4

Woodley Equipment Company 

 +44 (0) 1204 669033 

 [email protected] | Page 1 

 

M

ODEL 

D

ESCRIPTION 

Clinispin HORIZON  products are a  versatile  range  of centrifuges designed with 3 settings to process Chemistry, 
Coagulation or Platelet Poor Plasma and Urine specimens in the same unit. The maximum g-force of 2,000 xg makes 
Clinispin HORIZON compatible with most brands of tubes. Cycle settings can be changed to accommodate custom 
settings.

 

 
 

 

F

EATURES 

o

 

The first three (3) cycles are conveniently preset and labelled 

for your lab’s most common applications. Use the 

default cycles or customise them as needed.

 

 

o

 

If desired, the control panel can be temporarily locked on one cycle for error-free reproducibility.

 

o

 

Up to 10 cycles can be programmed for time, speed and braking and labelled with a custom name. Cycles can be 
programmed by g-force (RCF) rather than speed to facilitate matching validated cycles and manufacturer

s IFUs.

 

 

o

 

Lid lighting indicates the 

centrifuge’s

 status (ready, running, complete), informing the operator when tubes are 

ready for the analyser and preventing tubes from being left in the centrifuge longer than necessary (patent 
pending).

 

 

o

 

A traditional audible alert indicates the completion of the cycle. The audible alert can be muted.

 

o

 

Cool

Flow design prevents overheating of samples by using ambient air to keep specimens at room temperature.

 

o

 

The tube holders are fibre reinforced for high strength, durability and years of trouble-free use.

 

o

 

A clear lid permits safe observation of samples and optical calibration of speed.

 

o

 

The lid safety system prevents the centrifuge from operating unless the lid is closed and latched.

 

o

 

The lid safety system only allows entry into the centrifuge after the rotor has completely stopped.

 

o

 

The high-power brushless motor provides years of operation with no routine maintenance.

 

 

 

I

NTENDED 

U

SE 

General  purpose  laboratory  centrifuge  intended  for  safe  and  rapid  density  based  separation  of  fluids,  including 
physiologic fluids, in approved specimen receptacles for qualitative or quantitative test procedures. As a  general 
purpose  laboratory  centrifuge,  it  is  designed  to  also  run  other  approved  containers  filled  with  chemicals  (non- 
flammable, non-explosive, non-volatile and non-highly reactive only), environmental samples and other non- human 
body samples. This device is intended to be operated by properly trained personnel who have carefully read  the 
operating manual and are familiar with the function of the device. 

 

[Refer to the clinical laboratory method specified by the specimen receptacle manufacturer or established by the 
medical technology for the products applications.] 

 

 

W

ARRANTY 

Woodley Equipment Company warranties that this centrifuge is free from defects in workmanship and parts for 2 
years.

 

Summary of Contents for Clinispin Horizon 6 Flex















Reviews: