Woodland Mills Woodlander Operator'S Manual Download Page 6 | Manualshive

Page: 6 / 68

Woodland Mills Woodlander Operator'S Manual Download Page 6

2018-2023 Woodlander

™

(MAX) Operator’s Manual

GENERAL SAFETY RULES

0001675-M-EN: Rev C

Page of

4

64

07-Oct-2022

Read and understand all instructions. Failure to follow all instructions
listed below may result serious injury.

WARNING!

The  warnings,  cautions,  and  instructions  discussed  in  this  instruction
manual  cannot  cover  all  possible  conditions  or  situations  that  could
occur.   It must be understood by the operator that common sense and
caution  are  factors  which  cannot  be  built  into  this  product  but  must  be
supplied by the operator.

WARNING!

The trailer is not designed to carry any additional weight other than the
sawmill and trailer itself while being towed. Failure to heed this warning
could result in damage to the trailer and/or the sawmill.

Damage caused by towing additional weight will void the warranty.

WARNING!

The Woodlander

™

and Woodlander

™

MAX sawmill trailers are for

off-

road use only

. It is the owner’s responsibility to make the trailer

road-worthy if towing on improved roads, complying with all local laws
and regulations.

WARNING!

The Woodlander

™

and Woodlander

™

MAX sawmill

trailers are

not

designed for speeds exceeding

30

mph

[

50 km/h

].

WARNING!

«
...
4
5
6
7
8
...
»

Summary of Contents for Woodlander





































































Reviews:

No comments