Woodland Mills Woodlander Operator'S Manual Download Page 5 | Manualshive

Page: 5 / 68

Woodland Mills Woodlander Operator'S Manual Download Page 5

2018-2023 Woodlander

™

(MAX) Operator’s Manual

INTRODUCTION

Congratulations on your purchase and welcome to Woodland Mills! This manual gives you the
necessary information about your Woodlander

™

sawmill trailer so you will be able to use it

properly. The entire manual must be read and understood before using the trailer. If any
questions should arise that are not covered by this manual, please contact Woodland Mills, Inc.

The Woodlander

™

sawmill trailer is compatible with HM126, HM130 & HM130MAX sawmill and

track systems for milling logs while the trailer is stationary and firmly supported on the ground.
It is not intended to carry any additional weight or be used as a utility trailer.

The Woodlander

™

and Woodlander

™

MAX sawmill trailers are

off-road

trailers designed for

certain  applications  only.    We  strongly  recommend  the  trailer  not  be  modified  and/or  used  for
any application other than that for which it was designed.  If you have any questions relative to a
particular  application,  DO  NOT  use  the  trailer  until  you  have  first  contacted  Woodland  Mills  to
determine if it can or should be performed using the product.

For technical questions and replacement parts, please contact Woodland Mills, Inc.

OWNER'S RECORD

Please take a moment to record the following information about your

Woodlander

™

sawmill trailer. If you need to call for assistance, please be

ready to provide your model and serial numbers. This information will allow
us to help you more quickly when you call.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

0001675-M-EN: Rev C

Page of

3

64

07-Oct-2022

«
...
3
4
5
6
7
...
»

Summary of Contents for Woodlander





































































Reviews:

No comments