Woodland Mills Woodlander Operator'S Manual Download Page 38 | Manualshive

Page: 38 / 68

Woodland Mills Woodlander Operator'S Manual Download Page 38

2018-2023 Woodlander

™

(MAX) Operator’s Manual

10. LIGHTING

Using  the  hardware  listed  below,  install  the  taillight  bracket  and  country  appropriate  wire
harness.   Secure tail lights to the taillight bracket using M5 flanged lock nuts before mounting
taillight bracket to trailer.   Use cable clamps to secure wire harness to side plates down right-
side of trailer.   Tighten all bolts.   The M10 X 160 mm tongue bolts from the previous step can
now be tightened after wiring has been routed through the tongue.

On the European (

EU

) version, install the 4 side reflectors, 2 front reflectors, and 2 rear reflector

brackets and reflectors as shown on the following pages. There are no red/amber side lights on
the European wire harness like the ones included with the North American (

NA

) version.

4x

M8 X 25 mm
Flanged Hex

Bolt

1x Taillight Bracket

4x

M8 Flanged

Lock Nut

2x

Rear Reflector

Bracket

(EU Only)

8x

M6 X 20 mm

Hex Bolt

2x

Rear Reflector

(EU Only)

8x

M6 Flat Washer

4x

Side Reflector

(EU Only)

8x

M6 Lock Nut

2x

Front Reflector

(EU Only)

12x

M5 X 20 mm

Pan Head

Screw

(8x NA Only)

8x

Cable Clamp

14x

M5 Flanged

Lock Nut

(8x NA Only)

1x

Wire Harness

(NA Only)

1x

Wire Harness

(EU Only)

0001675-M-EN: Rev C

Page

of

36

64

07-Oct-2022

«
...
36
37
38
39
40
...
»

Summary of Contents for Woodlander





































































Reviews:

No comments