Woodland Mills Woodlander Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 68

Woodland Mills Woodlander Operator'S Manual Download Page 18

2018-2023 Woodlander

™

(MAX) Operator’s Manual

2. GUSSETS

Using the hardware listed below, assemble the gussets to the track as shown on the next page.

Ensure the track width is set correctly (see track widths on next page), and measure diagonally
to check for squareness. Torque all bolts per the table in section,

BOLT TORQUE

SPECIFICATIONS

.

Track components listed in these tables are

not

included with the trailer package, namely track

rails, reinforcement plates, bunks, and carriage stops. These components are found in the
sawmill crate. If the trailer was purchased for an existing sawmill (i.e. the sawmill is currently
assembled), the track will need to be disassembled prior to building the trailer and the following
assembly instructions performed.

24x

M10 X 30 mm

Flanged Hex

Bolt

2x

Mid Bunk

8x

M10 X 40 mm

Flanged Hex

Bolt

2x

Reinforcement

Plate

32x

M10 Flanged

Lock Nut

4x

End Gusset

2x

End Bunk

6x

Joining Gusset

1x

Centre Bunk

4x

Track Rail

0001675-M-EN: Rev C

Page

of

16

64

07-Oct-2022

Use the fasteners included with the

sawmill trailer to assemble the

track. The fasteners included with

the sawmill track will

not

be used.

«
...
16
17
18
19
20
...
»

Summary of Contents for Woodlander





































































Reviews:

No comments